You have to remove the brake pad from the pedal.It should have the wire harness, 2 micro switches, a metal bracket for mounting, and the mounting hardware once you are sure all the pieces are available, you can start the installation.Inspect the items included in the brake light switch kit you have received.If you have ordered the LGT-641 Club Car Brake Switch Kit, the following steps will help you to install it on your golf cart. and you will have to order them separately. Some of the light kits sold in the market may not contain the brake light switch etc. Whichever step fails the test, you can repair or replace the part and see if the brake lights work or not. You must check if it is receiving 12V current for it to function properly. There is a relay below the dash for the brake lights. Check if it is connected properly with the wires. You should be able to see the brake light switch there. You can then remove the floor mat below the pedal and inspect it. You can start with the brake light bulbs to see they are functional. It could be any of the switches, the bulbs, the relay, or the wires. To fix the problem of the brake lights not working in your club Car golf cart, you have to first identify the source of the problem. How to Fix Club Car Brake Lights Not Working? It could cause the issue of the brake lights staying on in the Club Car Precedent golf cart. In addition to all these, there is a pressure switch in the circuit. If the brake lights switch OFF after four minutes, that is a normal situation and you have no issue.If the lights still stay ON then you have an issue. If you find the brake lights ON, wait out the four minutes to see if the lights go OFF.Insert the key into the ignition and switch it ON.To verify this, follow these steps given below: You can also confirm if the relay is a timed one, in which case, the brake lights will stay ON for a while before switching OFF. If it remains pressed, the brake lights could stay ON. The other reason for the brake lights staying on in a Club Car is the floor mat blocking the brake pedal from gaining its position back. Some experts contest this as they say if the relay is faulty the brake lights won’t come on when the ignition is ON. You should replace the relay and the problem should get resolved. It could be the brake light switch as well. The problem occurs in cases where the relay failed when in the closed position. It switches OFF only when the ignition is turned OFF. The issue that most users of Club Car Precedent Electric (2010) come across is that once they apply the brake, the brake light comes and stays on even after the brake is released. The main reason why Club Car golf cart brake lights stay on is because the timer relay in the circuit is failing. You also need to check that the bulbs are fitted securely and that they are the correct rating of bulb. In the case of the brake lights in a Club Car golf cart, there are two brake lights at the rear and if both don’t light up, the problem could be elsewhere. If a light does not turn ON, you would check the bulb immediately. Make sure the green and blue wires are connected. These are usually of four colors – green, red, orange, and blue. Also take note of the extra wires coming from the light kit harness. This will complete the circuit for the brake light. This should be connected to the purple wire from the ultimate harness. If you have ordered a light kit, you will notice a brown wire going out from it. The above applies to the 2010 Club Car Precedent. While checking under the floor mat check the fuse that is meant for the brake lights as well. You may find a component like a brake light timer relay missing or malfunctioning and this will need replacement or repair. On many occasions, the brake light switch may be there but it may not be wired properly. This is one reason Club Car golf cart users are surprised when the brake lights do not come on when the brake is applied. The brake light switch does not form part of the light kit if you have ordered one. Most people buying a Club Car do not give much thought to the brake lights. You will have to remove the floor mat to access it. The brake light switch is mounted below the Club Car’s pedal. You have to check these two first before moving on to anything else. The frequently reported reasons for the brake light not working in a Club Car golf cart is either a faulty brake light switch or loose wiring. Why are my Club Car Brake Lights Not Working? Why are my Club Car Tail Lights Not Working?.Club Car Precedent Brake Light Wiring Diagram.How to Fix Club Car Brake Lights Not Working?.Why Do My Club Car Brake Lights Stay On?.Why are my Club Car Brake Lights Not Working?.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |